Final Assembly

Automatic or semiautomatic lines come equipped with advanced AI vision systems for component positioning and tolerance measurement. Wherever those are impractical, digital contact sensors can perform high-accuracy measurements of thickness, flatness, and parallelism. Servo-controlled presses handle delicate press operations, guided by force sensors for even distribution.

These lines are modular by design, allowing for easy adaptability and future upgrades. They also feature energy consumption measurements for both air and electricity, providing valuable data for optimizing operational efficiency. Integrated with MES systems, the lines offer streamlined operation and quality control.

Stopite v stik
Add-on

Functionality test

To ensure that only good parts are passed forward, various functionality tests are performed at the end of line. All test results and measurements are reported to the information system for 100%...

Add-on

End of line calibration

At end of line the products are calibrated to ensure the highest quality. The biggest challenge for the display calibration is white point calibration. This process requires specialized hardware...

Add-on

Manual test

If required, a manual test station can be positioned at the end of line. The product is contacted and powered up with specially designed images for the operator to determine any potential errors...

Add-on

Protection foil placement

After detailed product testing, protection foil for display and other critical cosmetic components is placed on the product to avoid any potential damage during the transportation and final...

Add-on
Functionality test
To ensure that only good parts are passed forward, various functionality tests are performed at the end of line. All test results and measurements are reported to the information system for 100% traceability. Even though there are multiple tests, failing just one will cause a part to be automatically rejected. The cause for rejection can be checked in the system and the product can be sent for an appropriate rework if it can be repaired. End-of-line testing usually consists of: ▪ Homogenity test, ▪ Touch test, ▪ Surface inspection, ▪ Sub-pixel test.
Add On
Add-on
End of line calibration
At end of line the products are calibrated to ensure the highest quality. The biggest challenge for the display calibration is white point calibration. This process requires specialized hardware and software, such as a colorimeter or spectrophotometer, to measure the display’s current white point and compare it to the desired target. Through adjustments to the display’s red, green, and blue color channels, the calibration software fine-tunes the color balance until the measured white point matches the target. To ensure highest quality product image centering is performed at the end. This process ofsets the center of the image on the LCD to match the center (the correct image position) in the final product.
Final Assembly
Add-on
Manual test
If required, a manual test station can be positioned at the end of line. The product is contacted and powered up with specially designed images for the operator to determine any potential errors following a strict set of criteria. The station is designed in such a way that it alows product height and tilt adjustment for various operator heights. This adjustment ensures ergonomy for the operator and better visibility angles for error detection.
Final Assembly
Add-on
Protection foil placement
After detailed product testing, protection foil for display and other critical cosmetic components is placed on the product to avoid any potential damage during the transportation and final product installation. The station conists of a protection foil feeder – usually supplied on a roll – and a robot. The robot uses force sensors and soft foam grippers to carefully apply the foil onto the required product area.
Final Assembly

Kontaktirajte nas

Vas zanima več? Pošljite nam svoje sporočilo, tako da izpolnite obrazec. Z veseljem bomo stopili v stik z vami v najhitrejšem možnem času.


    Vaše osebne podatke bo INEA d.o.o., Stegne 11, Ljubljana, na podlagi zakonitega interesa (komuniciranje s strankami in javnostjo, (točka f 1. odstavka 6. člena GDPR) obdelovala za namen odgovora na vaše vprašanje oz. poizvedbo. Vaše osebne podatke bomo hranili do zaključka naše komunikacije, nato jih bomo izbrisali. Če ste nam dali privolitev ( točka a 1. odstavka 6. člena GDPR), da želite prejemati vam prilagojene e-novice in ponudbe, bomo predvidevanja o vaših zanimanjih obdelovali na podlagi vaše uporabe naših storitev (nakupi, povpraševanja), do vašega preklica. Od prejemanja e-sporočil se lahko kadarkoli odjavite s klikom na povezavo v prejetem sporočilu. Več o obdelavi osebnih podatkov si lahko preberete v Politiki zasebnosti.